Component

Precision Parts

Tolerance is the whole job.

We set the process to the drawing, run a first article, measure it, and start the batch once it passes. If one feature needs a tighter band than the rest of the part, tell us and we will hold it there rather than to a blanket figure across the whole thing.

  • 0.01mm Tightest tolerance held on the parts below
  • 3 Routes: CNC machining, die casting and injection moulding
  • 1 First article measured before any batch starts

Set the process to the drawing

We make precision parts by CNC machining, casting and moulding, working to your drawing rather than to a catalogue. The components below are parts we have made for aerospace, automotive and medical customers: housings, brackets, covers and mounts, held to tight tolerance.

The route matters as much as the tolerance. CNC machining for parts cut from solid, die casting where the volume justifies a tool, and injection moulding for plastics. Send a drawing or a sample and we will come back with a price, a lead time and a route, rather than quoting the only process we happen to run.

A blanket tolerance across a whole part is usually the most expensive way to buy it. If one bore has to be right and the outside profile does not, say so, and the price follows the requirement instead of the drawing border.

If one feature needs a tighter band than the rest of the part, tell us and we will hold it there.

Rather than to a blanket figure across the whole thing, which is what most quotes price against.

What comes with the part

  • Aerospace, automotive and medical customers
  • Housings, brackets, covers and mounts
  • 3, 4 and 5 axis machining
  • First article measured and recorded before the batch
  • Inspection reports against your nominated parameters

Specification

Precision part tolerances and capacity

The figures below are what the parts further down were actually made to, not a capability ceiling.

Precision machined and moulded components
Processes CNC machining, die casting, injection mouldingQuoted against the drawing and the annual quantity, not against the process we would rather run.
Axes 3, 4 and 5 axis
Typical tolerance ±0.02mm to ±0.1mmWhat most of the parts on this page were run to.
Tightest held here ±0.01mmOn a single piece prototype, delivered in 10 days.
Feature level tolerance To drawingBand it per feature rather than across the part and the price follows the requirement.
Finish as standard DeburrPlating, anodising and blasting available through one finishing partner.
Quantities One off prototype to 5,000 and above
Lead times 10 to 30 daysAgainst the parts below. A prototype ran in 10, a 5,000 off frame in 30.
Sectors supplied Aerospace, automotive, medical

Send a drawing or a sample with the annual quantity and we will come back with a price, a lead time and a route. Request a quote.

Why buyers send us the hard drawings

  • 01

    Route chosen, not assumed

    Machined, cast or moulded, decided by the drawing and the quantity rather than by what we would prefer to run.

  • 02

    Tolerance per feature

    Hold the bore and relax the profile and the part gets cheaper without getting worse. That only works if someone reads the drawing properly.

  • 03

    First article before the batch

    Measured and recorded against your nominated parameters. The batch starts after it passes, not alongside it.

  • 04

    One supplier across three processes

    An assembly with a machined housing, a cast bracket and a moulded cover is one purchase order here.

  • 05

    Prototype through to volume

    A single piece at 0.01mm in ten days, or five thousand frames in thirty. Same drawing, same people.

  • 06

    Finishing on the same order

    Deburr as standard, and anodising, plating or blasting added through the same finishing partner rather than a chain of them.

Recent work

Parts we have actually made

Each card carries the quantity, tolerance and lead time that job ran to. Scan across to find one shaped like yours.

  • A machined metal part with cylindrical and circular features

    Machined cylindrical component

    Turned and milled from solid, concentric features held across one setup.

    Qty
    1,000
    Tolerance
    ±0.02mm
    Lead
    25 days
  • Rectangular metal component with a central circular cutout

    Machined plate with bored centre

    Flat plate with a bored centre, where the bore position matters more than the outline.

    Qty
    1,000
    Tolerance
    ±0.02mm
    Lead
    25 days
  • Four silver metal rectangular frames stacked in an offset arrangement

    Machined rectangular frames

    The largest run on this page, and the longest lead time because of it.

    Qty
    5,000
    Tolerance
    ±0.02mm
    Lead
    30 days
  • Machined metal engine cover with an intricate profile and a rubber seal

    Machined engine cover

    Sealing face machined after casting, which is where most covers fail.

    Qty
    1,000
    Tolerance
    ±0.02mm
    Lead
    25 days
  • Rectangular metal mounting bracket with four screw holes

    Machined mounting bracket

    Hole pattern held to the drawing so it drops onto an existing fixing.

    Qty
    5,000
    Tolerance
    ±0.02mm
    Lead
    25 days
  • Black metal camera mount adapter with a cylindrical body

    Machined camera mount adapter

    Anodised finish over a machined body, on a looser band than the parts above.

    Qty
    3,000
    Tolerance
    ±0.05mm
    Lead
    25 days
  • Black rectangular metal bracket with a central circular cutout and support ribs

    Machined bracket with support ribs

    Ribs add stiffness without adding material, and add setups to the machining.

    Qty
    3,000
    Tolerance
    ±0.05mm
    Lead
    25 days
  • Assorted machined metal and plastic parts arranged on a flat surface

    One off metal and plastic parts

    A single prototype set, to the tightest band on this page and out in ten days.

    Qty
    1
    Tolerance
    ±0.01mm
    Lead
    10 days
  • Two machined metal brackets on a plain background

    Machined brackets

    Standard bracket work, the volume this page mostly runs.

    Qty
    1,000
    Tolerance
    ±0.02mm
    Lead
    25 days

Quantities, tolerances and lead times above are the figures these jobs ran to. Yours will differ with material, feature count and finish, which is why we quote rather than publish a price list.

Why does a tighter tolerance cost more?

Because it moves cost from cutting into measuring, and measuring does not get cheaper with volume.

Going from ±0.1mm to ±0.02mm usually means slower feeds, an extra finishing pass and tighter tool change intervals. Going from ±0.02mm to ±0.01mm usually means a temperature controlled environment and measuring every part instead of sampling. The first step is a machining cost. The second is an inspection cost, and it scales with quantity rather than against it.

This is why banding per feature is worth doing. A bracket where one bore is ±0.01mm and everything else is ±0.1mm is close to the price of a ±0.1mm bracket. The same bracket drawn at ±0.01mm throughout can be several times that, for no functional gain.

How do you decide between machining, casting and moulding?

Annual quantity first, then the features the part needs.

Below a few hundred, machining from solid wins because there is no tool to pay for. Past a few thousand, the tool cost for casting or moulding amortises and the unit price drops away from machining sharply. The crossover is the number that matters, and it moves with the part.

Features push it either way. Thin walls and internal detail favour casting or moulding. Tight flatness, fine threads and sealing faces favour machining, or casting followed by machining just those faces, which is what most of the housings on this page are.

Send the quantity you need now and the quantity you expect annually. We will quote the route that costs least over the life of the part rather than the one that costs least this month.

What inspection comes with the parts?

A first article measured against your nominated parameters before the batch runs, and an inspection report with the delivery.

If your own approval process needs more than that, say so at enquiry stage. We run Advanced Product Quality Planning, the Production Part Approval Process, Failure Mode Effects Analysis and Repeatability and Reproducibility studies, and the requirement can change how the part is made rather than just what gets documented afterwards.

More on how that works on the quality page.

Machined fittings collected in a bin ready for dispatch

Get in touch today

Start with a drawing and a quantity

A single problem component, or a package you want off four suppliers and onto one. Tell us what you need and we will come back with a price, a process and a lead time.

Call us today on 01827 712910 Monday to Friday, 8am to 5pm · sales@coler.co.uk
  • The team picks up every quote within the hour
  • NDAs signed before you send anything sensitive
  • You speak to an engineer, not a call handler

Enquiry

Request a quote

Fill this in and the right person comes back to you. Got a drawing ready? Use the full quote form to attach it now.

This field is for validation purposes and should be left unchanged.
Name(Required)