Capability
Sand Casting
No permanent tool, almost no size limit, and viable at a quantity of one.
A mould packed in bonded sand around a pattern, poured, then broken away to release the casting. The mould is destroyed every time, which sounds wasteful and is in fact the reason it is the cheapest route to a large part or a short run.
- 1 Minimum quantity, because there is no tool to amortise
- 3 Main alloy families: aluminium, iron and bronze
- 100% Batches inspected by Coler before dispatch
How sand casting works
A pattern, which is a replica of the part, is packed into bonded sand to form a cavity. The pattern comes out, cores go in where the part needs internal passages, molten metal is poured in under gravity, and once it has frozen the sand is broken away. The casting is cut from its runners, cleaned up and inspected.
The mould is consumed each time. That is the whole economic argument: there is no hardened steel tool to pay for before the first part, so the entry cost is a wooden or resin pattern rather than a die costing tens of times more. One part is a sensible order.
It is also effectively unlimited in size. Where a die casting machine is capped by its locking force, a sand mould is capped by the size of the box and the capacity of the furnace. Engine blocks, pump casings, large housings and machine bases are sand cast for this reason.
The costs are surface finish and tolerance. A sand casting comes out rougher than a die casting and holds a looser dimension, because the mould face is compacted sand rather than polished steel. Anything that has to seal, locate or hold a thread gets cut afterwards through CNC machining, which is normal and is allowed for in the drawing.
There is no tool to pay for, so one casting is a reasonable order and a thousand is also a reasonable order. Very few processes are honest about both.
Why sand casting has not been replaced
- Alloys
- Al, iron, bronze
- Size
- 0.2kg to tonnes
- Wall thickness
- From 4mm
- Tolerance
- +/- 0.8mm as cast
- Surface
- Ra 6.3 to 25
- Quantity
- From 1
Also available
- Pattern making, in wood for low quantities or resin for repeat work
- Cores for internal passages and undercuts
- Heat treatment, because sand castings take it without blistering
- Full machining, so the part arrives finished rather than as a raw casting
Order to delivery
From drawing to finished casting
The pattern is the only tooling, and for a one off it can be made in days rather than weeks.
- Drawing reviewDraft, machining allowance and feeding checked before a pattern is cut
- Pattern makingWood for low quantities, resin or metal for repeat runs
- MouldingPattern packed in bonded sand, cores set for internal passages
- PouringMetal poured under gravity and allowed to solidify
- Knock outSand broken away, runners and risers cut off
- FettlingCasting cleaned up and shot blasted
- MachiningSealing faces, bores and threads cut to the drawing
- Coler inspectionChecked by us against the drawing before anything ships
For a one off or a prototype, the pattern cost is usually the whole tooling bill.
Request a quoteWhy buyers come to Coler for this
-
01
We chose the plant
We do not own the machines. We qualified the people running them over 25 years, we part funded a good deal of the plant, and we place the work where it actually fits.
-
02
The inspection is ours
Every batch is checked by us before it leaves. That is a second check on the plant, not a certificate you have to take on trust.
-
03
One order, one contact
Casting, machining and finishing go on one schedule and one purchase order, so the part does not sit waiting between two suppliers.
-
04
ISO 9001:2015
Held by Coler. The plants hold their own standards and we send the relevant certificate with the quote rather than waiting to be asked.
-
05
Specials, not catalogue
Almost everything here is made to your drawing. If you need it to a print, that is the normal job rather than the awkward one.
-
06
Stock held for you
Order up to twelve months ahead and call it off as you need it, which takes the lead time out of your own planning.
Read next
The rest of the casting picture
Four casting processes wear similar names and suit different parts.
-
Investment casting
Lost wax. The other expendable mould process, and far finer than this one.
-
Gravity die casting
A permanent steel mould, for when the quantity justifies one.
-
High pressure die casting
Thin walls and high volumes, at the other end of the range.
-
Industrial forging
When the part needs grain flow and strength a casting cannot give it.
-
Die casting overview
Start here if you have not chosen a process yet.
-
CNC machining
The faces, bores and threads we cut after the casting comes out.
-
All capabilities
Every process we place, with what each one suits.
-
Components
The parts we supply as specials rather than off a shelf.
-
Request a quote
Send a drawing and an annual quantity and you get a price and a lead time.
What are the advantages and disadvantages of sand casting?
Cheapest entry cost of any casting process. No permanent tool, so a pattern rather than a die, which is the difference between hundreds and tens of thousands.
Almost no size limit. Parts from a few hundred grams up to several tonnes, where die casting is capped by machine locking force.
Takes alloys other processes will not. Iron, steel and bronze all sand cast routinely and none of them can be die cast.
Heat treatable and weldable, because gravity pouring does not entrain air the way pressure injection does.
Against that: rough surface and loose tolerance. Expect Ra 6.3 to 25 and around +/- 0.8mm as cast, so allow machining stock on anything that has to seal or locate.
And slow, per part. The mould is rebuilt every time, so the piece price does not fall away at volume the way a die cast part does.
Sand casting or die casting?
Quantity and size decide it almost every time.
Sand if the part is large, the annual quantity is in the tens or hundreds, the alloy is iron or bronze, or you need one to test a design before committing to a tool.
Die casting if the part is small to medium, the annual quantity runs into the tens of thousands, the alloy is aluminium or zinc, and you want a good surface straight off the machine. Then choose between high pressure and gravity on wall thickness and duty.
A common and sensible route is to sand cast the first few to prove the design, then move to a die once the drawing is settled and the volume is real.
What tolerance can I expect?
As cast, plan for around +/- 0.8mm on a medium sized part, opening up as the part gets bigger. Sand is a compacted granular mould, not a polished steel one, so it will not hold what a die holds.
This is not usually a problem because it is designed around. You put machining stock on the faces that matter, cast everything else to shape, and cut the tolerance in afterwards. We machine on the same order, so the casting does not sit waiting between two suppliers.
Who pours it?
A foundry we have qualified, not one Coler owns. Coler does not own machines. We specify the job, choose the foundry, and inspect every batch before it leaves.
Coler Supply Solutions (Intl) Ltd holds ISO 9001:2015. The foundries hold their own standards and we send the relevant certificate with the quote.
Get in touch today
Start with a drawing and a quantity
A single problem component, or a package you want off four suppliers and onto one. Tell us what you need and we will come back with a price, a process and a lead time.
Call us today on 01827 712910 Monday to Friday, 8am to 5pm · sales@coler.co.uk- The team picks up every quote within the hour
- NDAs signed before you send anything sensitive
- You speak to an engineer, not a call handler
Enquiry
Request a quote
Fill this in and the right person comes back to you. Got a drawing ready? Use the full quote form to attach it now.